RAL 8025 Pale Brown Paint

Use standard RAL 8025 Pale Brown when acceptance is based on the RAL standard color target, not on matching an existing coated part.

• Standard RAL 8025 is suitable for: cross-material coordination where textures/sheens already differ; small touch-ups or functional protection; projects where minor sheen/texture variation is acceptable; and when inspection will compare to a RAL reference standard.
• Request a sample/OEM match when: the part will be inspected side-by-side against an existing coated part; large, high-visibility areas are being repainted; strict cosmetic acceptance criteria apply; or a specific OEM powder code is specified.
• Risks to manage: RAL is a color target, not a coating process. Liquid and powder coatings can look different in gloss/texture even at the same RAL code. Lighting strongly affects appearance-agree on the lighting conditions for evaluation. If acceptance is against an aged/faded part, a fresh standard RAL 8025 may not be accepted.
• To reduce risk, document finish details with the color: gloss level, texture, substrate, and inspection method (e.g., compare to RAL standard vs. to a supplied part).

Yes-if the existing coating is sound and you prepare it correctly.

• Assess: Ensure the old film is well-adhered, clean, and free of chalking. If acceptance is against the existing part color, consider a sample-based match because aged films often differ from the RAL 8025 standard.
• Prep: Degrease thoroughly, remove loose/failed coating, feather edges, and scuff-sand glossy or slick powder to a uniform dullness. Wipe clean and dry.
• Adhesion check: Perform a small-area scuff, apply your intended system (or adhesion/bonding primer), and run a simple cross-hatch tape test before full production.
• Touch-up vs. recoat: For small chips/scratches, direct application may be acceptable after scuff/clean. For larger areas or very slick/baked powders, use an adhesion-promoting or epoxy primer per the coating system guidance.
• Limitations: Fluoropolymer or silicone-modified powders, heavily chalked films, or contamination can inhibit adhesion-use appropriate primers or additional prep. Expect visual differences in gloss/texture when touching up powder with liquid paint.

Confirm the exact code, name, and acceptance basis before ordering.

• Verify the four-digit code and name: RAL 8025 Pale Brown. Common confusions include RAL 8024 (Beige Brown) and RAL 8023 (Orange Brown). Watch for transcription errors like 825 or 80025.
• Finish is separate: RAL Classic defines the color target only. Record finish requirements separately (e.g., gloss level, texture, substrate).
• Clarify what to match: Are you matching the RAL 8025 standard or an existing coated part/OEM powder? This determines whether a standard RAL product or a sample/OEM match is appropriate.
• Digital values are for reference only: RAL 8025 approximate display values are RGB 115,86,67 and Hex #735643; LRV ~ 10.73. Do not accept or reject by screen-evaluate under the intended lighting with physical standards.
• Purchase order tip: State the acceptance target, e.g., "Match RAL 8025 standard" or "Match supplied part labeled RAL 8025."

Primer needs depend on the substrate and the coating system.

• Bare carbon steel: Yes. Use a rust-inhibitive primer (epoxy or compatible system). For exterior or severe service, epoxy primer is preferred.
• Aluminum and stainless: Yes. Clean, abrade/scuff, solvent-wipe, then use an epoxy or suitable metal primer. Conversion coating or wash primer improves performance where allowed.
• Galvanized steel: Yes. Clean (remove oils/white rust), sweep blast or use pretreatment, then prime with a galvanized-compatible or wash/etch primer.
• Plastics (ABS, PVC, etc.): Typically yes. Clean thoroughly and use a plastic adhesion promoter; follow with a compatible primer if required by the topcoat system. Test unknown plastics first.
• Previously painted or powder-coated: If sound and properly scuffed, small touch-ups may not require primer. For larger recoats or slick baked powders, use an adhesion-promoting or epoxy primer.
• Always verify adhesion with a small-area test and align gloss/texture expectations, especially when transitioning between powder and liquid coatings.

Yes, our spray paint, paint pens and touch up bottles are ideal for touching up parts of all kinds, including powder coatings. However, keep in mind that our version of RAL8025 Pale Brown is based on the color swatch contained in the official RAL color book. The color and sheen of your specific production parts may be different. If you need a touch up application, we can create a touch up solution precisely matching your specific parts.

Learn more about our color matching service.

MyPerfectColor spray paint is a fast-drying durable acrylic enamel coating suitable for interior or exterior use. MyPerfectColor custom spray paint matched to RAL8025 Pale Brown enables you to conveniently achieve a professional spray-smooth finish in any color in any sheen. It sticks well to most surfaces including metal, plastics, powder-coatings, cabinets and primed or previously painted wood.

The MyPerfectColor 11oz spray can will cover about 20 square feet per coat. Keep in mind that it is difficult to gauge spray paint need as the coverage is highly dependent on how it is applied. Learn more about how spray paint works at MyPerfectColor.

While we can provide RAL8025 Pale Brown in paint, we don't provide any crossover information. We've found that every paint company offers its own unique selection of colors and rarely does a color have an exact equivalent in another brand.

However, under the color image on a color page there is a link that says "Explore Colors". Clicking this link displays colors with similar values and you can look for any colors from the brand you want.

Keep in mind that this just shows similar colors based on the color values we have stored in our database. It doesn't mean it is the same or give any approximation about how close the color is. You can play around with the Hue, Lightness and Chroma sliders to expand the selection.