RAL 7046 Telegrey 2 Paint

RAL 7046 Telegrey 2 defines the color target only. It does not specify gloss, texture, resin system, or coating process. Use this quick decision guide:

• Standard RAL 7046 is appropriate when:
  • Your spec simply lists "RAL 7046" and does not impose gloss/texture tolerances or inspection criteria.
  • You're doing low-criticality repairs (chips, small areas) for functional protection.
  • You're coordinating across materials (e.g., powder-coated parts near painted hardware) where some sheen/texture difference is already expected.
• Request a match to your specific part/OEM when:
  • Large, continuous or high-visibility surfaces are involved (panels, enclosures, facades).
  • Strict acceptance or inspection is expected, or prior rejections occurred.
  • The drawing calls for "match existing" or cites an OEM powder code/finish.
  • Existing parts have aged, or you suspect batch-to-batch variation.

Risk notes: Liquid vs powder can differ in gloss and texture, which changes perceived color. Mid-gray neutrals like RAL 7046 can lean slightly warm/cool between systems and under different lighting. If acceptance is tight, provide a physical sample or OEM code, specify required gloss/texture, and approve a spray-out before production.

Primer needs are driven by substrate and service environment, not by the RAL 7046 color. Use the following guidance:

• Bare carbon steel: Remove rust/scale; for general industrial use, apply corrosion-resistant primer (e.g., epoxy). For high-corrosion exposure, consider zinc-rich primer under an epoxy/urethane system.
• Galvanized steel: Light sweep blast or chemical pretreat to remove passivation. Use a galvanized-compatible wash/etch or epoxy primer to ensure adhesion.
• Aluminum (bare or anodized): Degrease and abrade. Use an etch or epoxy primer; for anodized, an adhesion promoter may be needed.
• Stainless steel: Thorough degrease and abrasion; epoxy primer recommended for adhesion.
• Plastics: Identify resin. Use plastic adhesion promoter; some plastics (PP/PE) may require flame or chemical treatment before priming.
• Previously coated surfaces (sound): Clean and degloss. For small touch-ups, primer is often only needed on exposed bare substrate; for broader recoats, a bonding/epoxy primer improves adhesion and uniformity.

Tip: Always verify adhesion with a small test area when substrate or existing coating is unknown. The RAL code sets color only-specify gloss and texture separately to manage appearance expectations.

Yes, if the existing coating is sound and properly prepared.

• Confirm acceptance target: Decide whether you are matching the RAL standard or the exact existing finish. For large/high-visibility areas or strict inspections, consider matching to an OEM powder code or submit a sample panel to avoid hue/gloss discrepancies.
• Surface prep: Clean thoroughly to remove oils and contaminants. Scuff-sand to degloss without cutting through where not needed. Feather any damaged edges.
• Adhesion check: Apply your intended primer/topcoat to a small test spot, allow cure, and perform a tape pull. If poor, use an adhesion-promoting or epoxy primer.
• Product compatibility: Avoid strong solvents that may soften the existing finish. Use systems labeled for repainting over cured powder or unknown coatings.
• Appearance risks: Gloss/texture differences and any aging on the original part can make a standard RAL 7046 look different even if the color target is the same. Align gloss where possible or approve a spray-out before full application.

For small chips and functional touch-ups, standard RAL 7046 is typically sufficient. For panel-wide recoats, validate adhesion and appearance on a test area first.

Yes, our spray paint, paint pens and touch up bottles are ideal for touching up parts of all kinds, including powder coatings. However, keep in mind that our version of RAL7046 Telegrey 2 is based on the color swatch contained in the official RAL color book. The color and sheen of your specific production parts may be different. If you need a touch up application, we can create a touch up solution precisely matching your specific parts.

Learn more about our color matching service.

MyPerfectColor spray paint is a fast-drying durable acrylic enamel coating suitable for interior or exterior use. MyPerfectColor custom spray paint matched to RAL7046 Telegrey 2 enables you to conveniently achieve a professional spray-smooth finish in any color in any sheen. It sticks well to most surfaces including metal, plastics, powder-coatings, cabinets and primed or previously painted wood.

The MyPerfectColor 11oz spray can will cover about 20 square feet per coat. Keep in mind that it is difficult to gauge spray paint need as the coverage is highly dependent on how it is applied. Learn more about how spray paint works at MyPerfectColor.

While we can provide RAL7046 Telegrey 2 in paint, we don't provide any crossover information. We've found that every paint company offers its own unique selection of colors and rarely does a color have an exact equivalent in another brand.

However, under the color image on a color page there is a link that says "Explore Colors". Clicking this link displays colors with similar values and you can look for any colors from the brand you want.

Keep in mind that this just shows similar colors based on the color values we have stored in our database. It doesn't mean it is the same or give any approximation about how close the color is. You can play around with the Hue, Lightness and Chroma sliders to expand the selection.