RAL 3014 Antique Pink Paint

Use the standard RAL 3014 Antique Pink when the color code is the acceptance target and exact replication of the original coating process is not required. RAL defines the color, not the gloss, texture, or film build.

Standard RAL is typically sufficient for:

• Cross-material coordination where textures/sheens already differ (e.g., metal panel near plastic trim).
• Low-criticality repairs (small chips, functional protection).
• Situations where close visual harmony is sufficient and the inspector compares to a RAL standard.

Choose a sample or OEM-specific match when:

• The acceptance standard is an existing coated part (not the fan deck).
• High-visibility cosmetic surfaces or large-area repaints are involved.
• Strict inspection criteria apply (defined light levels, gloss tolerance, or texture requirements).
• A known OEM powder code/finish exists and must be maintained.

Risk to manage: liquid paint and powder can differ in gloss and texture even at the same RAL color, and appearance shifts under different lighting. Confirm what the inspector will compare against and evaluate under your service lighting.

How to specify to reduce risk:

• If ordering standard RAL: specify "RAL 3014 Antique Pink" and include the required gloss range if any.
• If matching an existing part: provide a physical sample or the OEM/powder code, and state the acceptance target (match-to-part) plus desired gloss/texture.

Select by defect size, visibility, and control needed:

• Paint pen: pinpoint chips and scratches up to ~3 mm wide; fast, clean application on edges and hardware.
• Brush bottle: small nicks, fasteners, and localized spots up to ~2-3 cm; good control and film build.
• Aerosol spray: panels, blended areas, or mottled surfaces; best for feathering edges and minimizing touch-up witness lines.

Notes to manage appearance risk:

• On powder-coated parts, spray usually blends best; pens/brushes may leave a noticeable dab. Spray will not replicate powder texture.
• Match sheen: if the surrounding surface is significantly glossier or flatter, consider specifying gloss to align with the existing surface.
• Always test on a small area first and review under service lighting.

Yes, if the existing coating is sound and properly prepared. Follow this process:

• Clean: remove oils, wax, silicone, and chalking (detergent wash, rinse, dry). Solvent-wipe only after detergent cleaning.
• De-gloss: scuff-sand uniformly (e.g., fine abrasive pad or 320-400 grit) to create a mechanical profile.
• Repair: feather edges and spot-prime any bare metal or exposed substrate.
• Adhesion check: do a small test area; if it wrinkles or lifts, stop and strip or isolate with a compatible primer.
• Topcoat: apply RAL 3014 Antique Pink per product instructions; light, even passes reduce witness lines.

Notes:

• Unknown or soft, solvent-sensitive coatings can swell or wrinkle; test first.
• Powder texture will not be duplicated by liquid touch-up; align expectations if appearance-critical.
• Evaluate the color under the lighting where it will be accepted.

Primer choice depends on the substrate and service environment. Typical guidance:

• Bare carbon steel: remove rust/scale, then use a rust-inhibitive metal primer (epoxy or alkyd per system and recoat window). Choose epoxy for higher corrosion exposure.
• Galvanized steel: clean to remove oils/passivation, lightly scuff. Use a galvanized-compatible primer (wash primer or galvanized bonding primer) before topcoat.
• Aluminum or stainless: degrease and abrade. Use a self-etching or epoxy primer for adhesion.
• Plastics (ABS, PVC, polycarbonate): clean thoroughly, use a plastic adhesion promoter; some plastics require light scuffing. Always test adhesion.
• Previously coated, sound finish: after clean and de-gloss, many systems allow direct topcoat; spot-prime only where bare substrate is exposed.

For appearance-critical areas, also specify gloss level to align with the surrounding surface and verify color under service lighting before full production.

Yes, our spray paint, paint pens and touch up bottles are ideal for touching up parts of all kinds, including powder coatings. However, keep in mind that our version of RAL3014 Antique Pink is based on the color swatch contained in the official RAL color book. The color and sheen of your specific production parts may be different. If you need a touch up application, we can create a touch up solution precisely matching your specific parts.

Learn more about our color matching service.

MyPerfectColor spray paint is a fast-drying durable acrylic enamel coating suitable for interior or exterior use. MyPerfectColor custom spray paint matched to RAL3014 Antique Pink enables you to conveniently achieve a professional spray-smooth finish in any color in any sheen. It sticks well to most surfaces including metal, plastics, powder-coatings, cabinets and primed or previously painted wood.

The MyPerfectColor 11oz spray can will cover about 20 square feet per coat. Keep in mind that it is difficult to gauge spray paint need as the coverage is highly dependent on how it is applied. Learn more about how spray paint works at MyPerfectColor.

While we can provide RAL3014 Antique Pink in paint, we don't provide any crossover information. We've found that every paint company offers its own unique selection of colors and rarely does a color have an exact equivalent in another brand.

However, under the color image on a color page there is a link that says "Explore Colors". Clicking this link displays colors with similar values and you can look for any colors from the brand you want.

Keep in mind that this just shows similar colors based on the color values we have stored in our database. It doesn't mean it is the same or give any approximation about how close the color is. You can play around with the Hue, Lightness and Chroma sliders to expand the selection.