70% of Orders Ship within 3 Business Days.
Match of Cerakote™ Satin Aluminum F-112 *
Actual color may vary from on-screen representation. Please view a physical color swatch or material sample to confirm your color choice prior to purchase.
Ready to purchase? Select your options in the 4 steps below.
A match of Cerakote Satin Aluminum F-112 is a very light, cool-leaning silver gray with low saturation and a soft satin metallic character. It reads as pale aluminum rather than a warm gray, and the finish effect is subtle rather than glossy or strongly reflective.
For touch-up after transportation damage, installation damage, fabrication work, service wear, or missed spots in the original finish, MyPerfectColor precisely matches the color and finish so repaired areas can stay aligned with the surrounding coated part. It can also be used on brackets, housings, trim pieces, screw heads, fastener covers, end caps, and sample panels where a small spray-applied match is needed on a coated assembly.
Because this is a very light metallic finish, thin coverage over a darker substrate may show contrast, and gloss or film build differences can change how the color reads at the repair edge. Small touch-up areas beside an older cured finish can also look different from the original part even when the color reference is correct, so finish matching matters as much as color matching.
Similar colors:
Product Data
About Cerakote Paint
Cerakote® is the world leader in firearm coatings. Since 1984, Cerakote has focused on developing and manufacturing ceramic coatings which are used by more firearm manufacturers than any other firearm coating.
Matching Cerakote Paint Colors
MyPerfectColor is able match most of the Cerakote paint colors in touch up paint. MyPerfectColor uses its expert capabilities to precisely match the color and sheen of the original Cerakote color by matching the original Cerakote swatches (when purchasing spray paint, paint pens and brush in cap bottles). MyPerfectColor is not using Cerakote paint.
The colors shown on this website are computer video simulations of the Cerakote Color and may not match Cerakote Color standards. Refer to Cerakote Publications to obtain the accurate color. Please know that MyPerfectColor is matching the original Cerakote color. If you intend to touch up paint that is old, know that your color has undoubtedly changed from the original due to exposure to light and age and the new paint may not match. You will achieve best results by re-coating the entire surface.
If you need more assistance, please feel free to contact us and one of our expert staff would be happy to help.
Frequently Asked Questions About Match of Cerakote™ Satin Aluminum F-112 *
Will MyPerfectColor matched to Cerakote Satin Aluminum F-112 537700 look exactly the same as my older cured finish?
MyPerfectColor precisely matches the color and finish, but an older cured part can still read differently next to a fresh repair. Gloss, texture, metallic effect, age, weathering, substrate, and batch variation can all change how Cerakote Satin Aluminum F-112 537700 appears in real use.
If the repair will sit beside an existing coated part, the safest choice is to compare against the actual part or an approved sample when the tolerance is tight.
Is Cerakote Satin Aluminum F-112 537700 a good match for touch-up after shipping damage, installation damage, or missed spots?
Yes. Cerakote Satin Aluminum F-112 537700 is a common reference for touch-up after transportation damage, installation damage, fabrication damage, drilled holes, cut edges, field modifications, chips, scratches, rub marks, or missed spots in the original finish.
MyPerfectColor custom-matched paint is made to precisely match Cerakote Satin Aluminum F-112 537700 so you can repair the affected area and keep the color and finish aligned with the surrounding coated part.
Can Cerakote Satin Aluminum F-112 537700 be used on plastic snaps, screw heads, trim plugs, or other hardware that cannot go through the original process?
Yes, if the part can be painted and needs to coordinate with a coated assembly. Cerakote Satin Aluminum F-112 537700 is often used as a reference for ancillary items such as plastic snaps, screw heads, rivet heads, clips, covers, trim plugs, end caps, brackets, and other small hardware.
For those parts, MyPerfectColor paint matched to Cerakote Satin Aluminum F-112 537700 helps the item blend with the surrounding finish, but surface prep and primer choice still depend on the substrate.
If Cerakote Satin Aluminum F-112 537700 is a liquid coating reference, why can a fresh touch-up still look different from the cured finish?
Because the reference color and the installed finish are not the same thing. MyPerfectColor precisely matches the color and finish, but a cured part can still look different from a fresh touch-up due to gloss, texture, metallic response, film build, cure, substrate, and age.
That means a correct match to Cerakote Satin Aluminum F-112 537700 can still show a visible difference beside an older coated part. If the area is highly visible or the part has aged, compare against the actual part or an approved sample when possible.
What surface prep should I use before applying Cerakote Satin Aluminum F-112 537700 to metal, plastic, or a previously coated part?
Start by cleaning and degreasing the surface, then remove loose contamination before painting. Light scuffing can help when the substrate and part condition allow it, but bare metal, plastic, and previously coated surfaces do not all prep the same way.
Use primer when the substrate or the existing coating needs adhesion help, and avoid coating over loose paint or residue. If you are unsure which prep route fits Cerakote Satin Aluminum F-112 537700 on your part, test a small area first or compare against a sample before committing to the full job.
How quickly will I receive my paint matched to Cerakote Satin Aluminum F-112?
Can I use this as touch up paint for the Cerakote Satin Aluminum F-112 coating?
Yes, you can use the acrylic enamel paint as a touch up for the Cerakote Satin Aluminum F-112 coating. MyPerfectColor precisely matches the color and sheen of the official Cerakote color sample. However, there may be some variation to your specific coating material due to aging, paint differences and application method. For ultra-critical matching requirements, you may consider having MyPerfectColor create a touch up solution precisely matching the color and sheen of your specific coating batch by sending us an actual part.
Learn more about our color matching services.
What type of paint is used to make touch up for the Cerakote Satin Aluminum F-112? And how much area will one can of spray paint cover?
To make touch up paint for the Cerakote Satin Aluminum F-112, MyPerfectColor uses an acrylic enamel which is a fast-drying durable coating suitable for interior or exterior use. MyPerfectColor custom spray paint enables you to conveniently achieve a professional spray-smooth finish in any color in any sheen. It sticks well to most surfaces including metal, plastics, powder-coatings, cabinets and primed or previously painted wood.
MyPerfectColor offers two spray can sizes - 11oz net weight and 4.5oz net weight. The 11oz spray will cover about 20 square feet per coat. The smaller can, which is perfect for manufacturers who want to include a can with product shipments, will cover about 7 square feet.
Will the paint match both the color and the sheen of the original Cerakote Satin Aluminum F-112 coating?
MyPerfectColor acrylic enamel paint matching the Cerakote Satin Aluminum F-112 will match both the color and sheen. MyPerfectColor precisely matches the original coating to serve as touch up paint. MyPerfectColor is matching from original Cerakote metal swatches. There may be variation due to batch processes, aging and paint type differences. Learn more about touch up paint solutions.
How does MyPerfectColor match paint to the Cerakote Satin Aluminum F-112 color?
MyPerfectColor has the original Cerakote Satin Aluminum F-112 sample in our color archive. We are able to make paint and verify that it matches the original.
Please note that there maybe differences between the color sample in our archive and your materials due to variation in manufacturing processes, aging, etc.
MyPerfectColor matches the Cerakote Satin Aluminum F-112 by scanning the sample with state of the art spectrophotometer and color matching software. The color match is refined through an iterative process to improve the match accuracy of both the color and sheen. MyPerfectColor has an extensive pigment library of over 100 different pigments that include organic and inorganic dispersions, aluminum, bronze and mica-based metallics and pearlescents, and fluorescent pigments. MyPerfectColor can achieve any sheen between flat and gloss. Note that difficult to match colors like metallics, pearlescents, and fluorescents will not match precisely - MyPerfectColor will get as close as possible, but the quality of these matches will not be as good due to the inherent limitations of matching these types of effect colors. Learn more about our color matching services.
Do I need a primer for Cerakote Satin Aluminum F-112?